Denon DN-M1050R Instrucciones de operaciones descargar pdf (Pagina 16)

ENGLISH

(9) Incrementing Track Numbers

During recording, track numbers can be incremented either

manually or automatically.

•

Track numbers can be incremented manually in the following

four ways:

1) Press the REC button (

●) during recording. This increments

the track number.

2) Press the PLAY/PAUSE button (

13) during recording to

stop recording for that track number and set the recording

pause mode. When the PLAY/PAUSE button (

13) is

pressed again, recording starts with a new track number.

3) Press the STOP button (

2 ) during recording to stop

recording for that track number and set the stop mode.

Now set the recording mode again. Recording starts with a

new track number.

4) After recording, use the divide function.

•

Track numbers can be incremented automatically in the

following three ways, according to the type of input signal:

Input type Method

Analog/digital input Detection of soundless section 1)

Digital input

CDs

and

MDs

Detection of soundless section 1)

Using the CD’s or MD’s subcodes 2)

Detection of soundless section 1)

Using the DAT’s start IDs 3)

DATs

1) Detection of soundless section

I Make the following two presettings:

• Set “Auto Inc OFF” (4) to “Auto Inc Det.”

• Set the soundless detection level setting to “Inc. Det.-(60)

dB” (5).

II Start playback and recording in such a way that the beginning

of the sound is not missed. When a soundless section (or a

section with level lower than the preset soundless detection

level setting) of at least 2 continuous seconds is detected, the

disc’s track number is automatically incremented.

2 seconds or more

Track number is incrementedSoundless section

NOTE: The auto track increment function may not work when

recording analog signals containing much noise. In this case

lower the detection level to for example –54 dB.

2) Using the CD’s or MD’s subcodes (digital input)

I Make the following presetting:

• Set “Auto Inc OFF” (4) to “Auto Inc Dig.”.

II Start playback on the CD (MD) player and recording on the

recorder in such a way that the beginning of the sound is not

missed. The disc’s track number is automatically incremented

when the CD’s (MD’s) track number changes. Changes in the

CD’s (MD’s) track number will not be detected for

approximately 4 seconds after the track number is

incremented.

NOTE:

The auto track increment function using the DAT’s start ID or the CD’s sub codes will not work if the digital input is in professional format

(AES/EBU). Input digital signals of the consumer format (SPDIF).

When recording from the DN-C680, set the presettings on the DN-C680.

CD/MD

12345

Copy

Track

number

Track A Track B Track X Track Y Track Z

Previously recorded

tracks

Tracks recorded

from the CD (MD)

Start of recording

Start of recording End of recording

Track X Track Y Track Z

Track

number

DAT

12345

Copy

Track

number

Track A Track B Track X Track Y Track Z

Previously recorded

tracks

Tracks recorded

from the DAT

Start of recording

Start of recording End of recording

Track X Track Y Track Z

Track

number

3) Using the DAT’s start IDs (digital input)

I Record the start ID on the recorded DAT.

II Make the following presetting:

• Set “Auto Inc OFF” (2) to “Auto Inc Dig.”

III Start playback on the DAT player and recording on the

recorder in such a way that the beginning of the sound is not

missed. The disc’s track number is automatically incremented

when the DAT’s start ID is detected. The start ID will not be

detected for 15 seconds after the track number is

incremented.

(10) Pre-UTOC Function

•

Presettings must be set. (Refer to Page 42.)

This function protects the recording should the power supply be

cut off. The UTOC is written directly after recording starts.

(The pre-UTOC is written.)

Normally the UTOC is written after recording is completed, so if

the power supply should be cut off during the recording or directly

after the recording is finished, the recording will not be registered

on the disc. To prevent this, the pre-UTOC (*1) is registered on

the disc directly after recording starts. Once recording is

completed normally, the actual UTOC (*2) is written. If the power

should be cut before the actual UTOC is written, the disc can be

played according to the pre-UTOC. This way you never

accidentally lose recordings that cannot be made over again.

01Tr 02Tr 03Tr

Pre-UTOC (*1)

Entire disc

Start of recording

End of recording

UTOC (*2)

If some problem occurs and recording is interrupted, the same

recording and UTOC can be written using the following editing

operation:

Use the divide function at the point where recording was

interrupted in track 03 on the above diagram to divide the track,

then use the erase function to erase track 04.

Input signal

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 45 46

Comentarios a estos manuales

Sin comentarios

Denon DN-M1050R Instrucciones de operaciones Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Controladores de dj Denon DN-M1050R